Customer had these 10m long cables and wanted to make 4 x shorter 5m ones out of two. Expensive – but very high quality – locking 6.35mm in-line sockets from Neutrik (excuse the messy paper towel!): Then the other end, used Rean RP3C-BAG – could be classed as ‘Neutrik-lite’ plugs: Coiled back up (properly – […]
Couple of Neutrik 1/4″ jack extension cables halved Read More »
Customer had this unit stored away for years and wanted to use it again, but found it wasn’t working properly, making an awful buzzing sound. This Akai 4000DS MkII is a nice machine but in a bit of a state perhaps was in a damp area, had to clean a good portion of switches (particularly
Akai 4000DS MkII reel to reel repair and service Read More »
Customer brought this nice unit in to look at as two meter lamps were out, wanted them sorting and also needed investigation/service as had some concerns over the calibration and signal routing (Master fader not working). Took out the meter panels and the master module (which turned out to be ok in the end, just
Soundcraft 400B studio mixer service and meter lamp upgrade Read More »
This came in because the owner said one of the input jack sockets has fallen inside the unit, and one channel not working as expected, so wanted that fixed and a general service. The plastic retaining screw was missing/broken and led to the connector being unsecured: Noticed a non-original pot fitted too, and a couple
Roland Jazz Chorus-120 repair and service Read More »
Customer acquired this effects unit but there was a broken knob that was tried to be glued back in place, only fix is replacement, which was fairly awkward to get to, and all of the pushbutton retaining clips were breaking off due to aged brittle plastic which made things a bit trickier as they kept
TC Electronic G-Major broken encoder repair Read More »
Customer said was using mixer and just died mid-performance, had been difficult to power up a few times previously but once running was ok, now doesn’t power on at all. Dead PSU. Tested and wasn’t getting power to pins on connector, which looks like a custom moulded plug for the Spirit mixer, making replacement a
Soundcraft Spirit Folio FX-8 mixer not powering up Read More »
Customer states unit exhibited a burning smell and sparks coming from fan area back right side of unit halfway through a performance and asked me to take a look to see what the issue was. First needed to repeat customer concern before doing anything in case act of opening up case changes something. Powered up
Dynacord Powermate 600-3 sparking behind fan Read More »
Customer had spent hours trying to find/fix a noise problem on their expensive microphone (just outside of warranty) so asked me to take a look, from the explained symptoms I suspected preamp valve noise, this microphone has the Abbey Road Studios REDD.47 preamp built in, and uses EF86 and E88CC valves. Repeated the problem (intermittent
Chandler REDD microphone intermittent noise Read More »
Customer brought in a rather tatty looking Rotel RA-1000, clearly had a good life (think ‘ex-pub’), but had some issues, and wanted a longer mains lead fitting On testing, left channel no output, turned out to be a physically broken ALPS remote rotary switch, made of unobtainium, so had to effect a repair. Metal slider
Rotel RA-1000 service Read More »
Customer brought their RCF sub in, was working ok then suddenly went into protect and no longer starts up and makes a click sound every other second or so. Inside we see Digipro 1000s – a £300 replacement module unit. Sod that, let’s fix it… As long as it’s not firmware on that microcontroller! Unit
RCF Art902 Active Sub (Digipro 1000s) stuck in protect Read More »
Customer had this R2R in storage for over 15 years, came out to use and found that the capstan was not moving, but the reels would spin, asked me to take a look. Confirmed the symptoms, no capstan movement (and no motor whirr when tension arm lifted). Could see belt was non-existent but should have
Teac TASCAM 22-4 4 track 1/4″ R2R no capstan movement Read More »
Customer had original DX-7, presented with a nasty pop and burning smell, and a ‘dodgy’ output jack. This keyboard was made for servicing, a few screws and the lid hinges up. Lovely. Then the cause of the stink was obvious, infamous RIFA suppression cap gone south: Also noticed memory backup battery (soldered to board) which
Yamaha DX-7 repair and checkup Read More »
